Commercial · Fort Myers, FL
When warehouse epoxy flooring fails, operations slow down, coatings peel, and joints spall under forklifts. Elite Epoxy Fort Myers has served Fort Myers since 2016 with epoxy floor installation and repair built for racking, pallet jacks, and daily wash-down.
Prep and base determine whether a warehouse floor lasts. We start with a slab evaluation (moisture-vapor emission, surface profile, and flatness at joints), then diamond-grind or shot-blast to ICRI CSP 2-4 for proper mechanical bond. Oil and tire-mark contamination gets degreased and rinsed, cracks are chased and filled with epoxy gel, and spalls are rebuilt with epoxy mortar. If moisture is high, we install a moisture-mitigating epoxy primer before the build coat so the system does not blister later.
After the base is sound, we tailor the finish to your traffic and cleaning routine. For warehouses that need chemical and abrasion resistance, we install 100 percent solids epoxy with a broadcast media (silica sand or aluminum oxide) for slip control, then lock it in with a high-solids epoxy or polyurethane topcoat. Where UV exposure is a factor at dock doors, we add a polyaspartic or aliphatic urethane topcoat to reduce ambering and chalking. We stripe traffic lanes, forklift paths, and safety zones with industrial line paint and can add cove base at walls for easier wash-down.
Fort Myers facilities choose us because we work like a contractor, not a paint crew. You get clear system options (epoxy, epoxy mortar, urethane cement hybrids where needed), realistic cure-time planning, and a written scope that calls out prep method, mil thickness, and slip-resistance level. Our crews are licensed and insured, and we keep projects organized around your receiving schedules, racking, and staged inventory so downtime is controlled.
At closeout we do a walkthrough with your manager and document what was installed, including the prep method, coating type, and maintenance guidance for auto-scrubbers and degreasers. You get clean edges, consistent texture, properly sealed joints, and crisp striping that stays visible under traffic. We also provide repair recommendations for high-impact areas like dock plates, forklift turns, and expansion joints so you can budget before failures spread.
Most garage floors are completed in 1-2 days depending on prep, repairs, and the coating system. Cure times vary, but many polyaspartic topcoats allow faster return to service than epoxy alone.
Sometimes, but we have to verify adhesion and compatibility first. We typically grind to remove weak layers and create a bondable surface, then prime and recoat with a compatible epoxy or polyaspartic system.
Yes, metallic epoxy is available for showpiece interiors, offices, and retail areas where a high-gloss decorative look is the priority. We finish with a clear protective topcoat and can add traction where needed.
Moisture vapor can cause bubbling, whitening, or delamination. We evaluate the slab and, when needed, install a moisture-mitigating epoxy primer designed to handle elevated vapor transmission before building the coating system.
Some products have noticeable odor, especially certain solvents and fast-cure resins. We select products based on the space and ventilation, and we communicate what to expect before the job starts.
Warehouse epoxy flooring is a system, not a single coat of paint. The best results come from the right concrete prep, the right resin chemistry for your traffic, and details that hold up at joints, dock doors, and turning lanes. Elite Epoxy Fort Myers installs and repairs industrial epoxy floors for distribution, light manufacturing, cold storage support areas, and high-traffic storage spaces where forklifts, pallet jacks, and carts grind coatings down fast.
Most warehouse floor problems trace back to poor prep or the wrong product. We verify the slab condition, remove weak laitance, and build a profile that allows 100 percent solids epoxy to lock into concrete. Cracks, pop-outs, and worn joints get repaired before coating so the finish does not telegraph defects. When slabs show moisture risk, we specify a true moisture-vapor barrier epoxy primer, then apply the build coat at a controlled thickness for durability under point loads and hard-wheel traffic.
Finish selection depends on how you use the space. For heavy abrasion and frequent cleaning, we can broadcast aggregate into epoxy for traction, then seal it with a high-wear urethane or polyaspartic topcoat. If your operation includes hot-tire pickup, oils, or chemical exposure, we match the system to the exposure and recommend cleaning products that will not soften the film. Lane striping, bay marking, and safety colors are installed after the field coat cures so lines stay sharp and bonded.
If your floor is already coated, we can repair and recoat without guessing. We test adhesion, identify delamination, grind to sound material, and feather repairs so you do not get raised edges that catch pallet jacks. The goal is a warehouse epoxy flooring system that stays serviceable, looks professional, and protects your concrete while keeping your facility moving.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Fort Myers. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
